Asphalt Shingle Blistering








Edward Fako
October 22, 2017 · Algonquin, IL ·
The Next Time An Adjuster States That The Surface Shingle Granule Displacement Is Caused By Blistering, Just Thank Him For Approving The Claim.
Why?
Because Shingle Blistering by and of itself does Not erode the shingles or pop the blister. It would typically take an outside force landing on the blistered shingles to actually erupt them and expose the asphalt protective coatings and reinforcement fabrics.
Basically, blisters typically only pop when they are struck be an outside force, such as Hail.
Read this article to learn how blistering occurs during the manufacturing process from trapped moisture remaining prior to the interior coatings and reinforcement fabrics have had the opportunity to cure and flash out its contained solvents.
https://inspectapedia.com/ro…/Asphalt_Roof_Blister_Cause.php
Causes of Shingle Blisters & Blister Rash on Asphalt Roof Products
Uniform asphalt shingle blister rash (C) Daniel Friedman
Asphalt Shingle Blister Rash - is a manufacturing artifact caused by trapped moisture vapor or solvent gas bubbles. The evidence & the science are explained here.
Rash blisters on asphalt shingles result from the manufacturing process, (and may be cosmetic or possibly a more serious defect) which are sometimes mistaken for hail damage or other types of asphalt shingle roof wear or damage indicators.
Note: separately at BLISTERS on ASPHALT SHINGLES we discuss the identification of asphalt shingle blister rash, how it is distinguished from other types of roof damage including hail damage, and we review the effects of blistered shingles on remaining roof life.
The most likely causes of asphalt shingle blisters or "blister rash" visible in product right from the factory is the expansion in gas form of either moisture trapped in the shingle substrate at the time of manufacture or gases from volatile organics or resins used in the shingle construction. Either of these can produce trapped gas bubbles as the shingles are exposed to high temperatures during production.
Shingle blisters might be caused as well by excessive use of roofing mastic or additional adhesives that are applied during or after roof installation. A warning to this effect issued by GAF Materials Corporation is found at WIND DAMAGE to ROOFS.
In such a case of adhesive-caused blister rash, the blisters ought to appear in a pattern that matches the blobs of adhesive, not in the regular pattern such as shown in our photo at above left (click to enlarge).
Role of Attic Temperature & Moisture Levels in Asphalt Shingle Blister Rash?
Shingle blisters converted to pits and damage (C) Daniel Friedman
Other somewhat more mixed or speculative theories blame asphalt shingle blister rash on attic ventilation or attic temperatures beneath installed roof. Although some sources including a State Farm Insurance Company PDF (statefarm.com/_pdf/roofing-composition-shingle.pdf) and a roofing website (pattoncontracting.com/roofing-blistering.htm) am not sure they are entirely correct.
Blister rash can be found on new asphalt shingle product that has never been rained-on - shingles right out of the factory-wrapped bundle.
That an asphalt shingle blister can by mechanical damage or mere weather exposure convert to exposed shingle substrate and even ultimately to shingle damage is suggested by our photo at left.
Experts place the underlying cause on moisture content or volatile solvent gas content of the material upon which the shingle is built (in the factory), if a felt or resin-filled fiberglass substrate is inadequately moisture-resistant and is wet at the time of manufacture or if there were inadequately cured resins or binders that then might outgas during manufacture those are the most likely sources of blistering.
It seems to me that although on the roof shingles can become quite hot, they probably do not reach the same temperatures as during manufacture. For blister rash to be caused by moisture after the roof is installed we would have to argue that the shingle resins or binders are soft enough that combined with moisture or VOC presence tiny bubbles of gas form within a near-liquid material. In my view that seems less likely than such formations during shingle manufacture.
Diagnostic in the assertion that field conditions contribute to or cause blistering would be to find credible reports that blister rash appeared on asphalt shingles after installation, with some compelling evidence that it was not present when installed.
I would also expect field-caused asphalt shingle blister rash to be progressive in appearance and for its occurrence to correlate with a sequence of weather conditions such as rain, temperature variations, sun exposure, etc. (Beware that often a pre-existing condition is seen as "new" or "just occurred" when in truth it was always there but simply was not noticed previously.)
Field Investigation of Asphalt Shingle Blister Rash Patterns vs Proposed Causes
Asphalt shingle blisters on Atlas Chalet shingles 4 years old (C) Daniel Friedman Jim todd
If asphalt shingle blistering were principally caused by a hot attic we'd expect to see a correlation with finding blisters and bad attic venting and moisture exposure and documented proof that the blisters were not present at time of roof installation.
I suspect that the reason attic temperatures entered into the urban lore on asphalt shingle blister rash is that experts have cited trapped moisture and heat as an original cause of blister rash - one can place this effect in the manufacturing process well before in field service.
That is, blistered shingles are evident in new product right out of the bundle not just on installed roofs. Furthermore blisters on installed asphalt shingle roofs that I have personally inspected have not once been found in patterns that correlated to attic moisture exit points (roof sheathing butt joints, roof penetrations for example) nor to sun exposure of individual roof slopes, nor even to the detailed thermal stress patterns in individual shingles documented by Cash & Kan.
Rather I see blistered shingles from individual bundles of shingles that may be installed rather uniformly over a large roof area on various slopes, or depending on the product delivered, installed in patterns consistent with how shingles were pulled and nailed from individual shingle bundles during roof installation - in some cases leaving a blistered shingle immediately next to a smooth un-blistered shingle and forming a strong argument against in-situ causation of the blistering.
The most scientific study of asphalt shingle blistering I've found was by Cash & Kan (cited below). Cash & Kan found that shingle blisters are a manufacturing defect traced to either moisture in the shingle substrate (damp felt or damp fiberglass mat) and/or inadequately cured resin in the shingle base during manufacture.
Cash & Kan's findings in their cross-sectional analysis of blistered roof shingles were quite consistent with my own forensic study of paint blistering (found at PAINT FAILURE LAB ANALYSIS) where cross-sectional microscopic analysis of blisters in a pinated [sic] surface showed physical evidence consistent with blisters formed in still-pliable materials as heat caused volatile gases to produce small bubbles in the material substrate.
Quoting Cash & Kan:
We obtained one regular radiographic (x-ray) image and several axial images (vertical sections) through each of the samples. As expected, some of the axial images of the blistered shingle clearly show the blisters extending through the top coating (Fig. 10).
The axial images of the unexposed and un blistered shingle show small bubbles in the coating at elevation of the
glass fiber felt (Fig. 11), suggesting the mat was moist or the mat binding resin was incompletely cured when the shingles were manufactured.
In further lab testing of asphalt shingle standards and materials for blister resistance (Behavior of Heating - ASTM D228, SGH Blistering Test, and Bubbling Test, European Standard prEN 544) in only the third test, the European Standard prEN 544 were Cash et als able to duplicate the same shingle blistering pattern as seen in field-installed products.
Quoting McNulty
ARMA has defined blisters as “hollow raised areas of variable size and shape which develop on the exposed surface of asphalt roofing upon exposure to the weather.” Blisters are normally of two types—small rash blisters and large blisters in which the entire thickness of the coating asphalt is raised from the felt and contributes to the deterioration of the roofing.
The evidence to date indicates that blisters are formed as a result of the behavior of entrapped air and moisture when subject to certain heat or temperature conditions. When excess amounts of solvent* based roofing adhesives are used, the shingle will absorb the solvent and the process is the same as for moist air. Dry air expands, on warming, in direct proportion to the increase in temperature.
Water, on the other hand, expands approximately 1,244 times in changing from a liquid to a vapor. Thus, if a shingle absorbs moisture which is trapped in the small voids in the coat* ing asphalt, this air will, at roof temperatures, expand and form blisters.
Blister formation can be minimized by ensuring the use of dry felts, saturating to the maximum possible without creating “wet spots” of saturant, ensuring the finished product is stored in a dry environment, and by minimizing moist air accumulation in attic areas by proper venting. The use of recommended amounts of roofing cement for tabbing and low slope shingle application is, of course, a necessity.
Rash blisters generally will not vent and should not pose a threat to the integrity of the roof. Large blisters (greater than 6.5mm in diameter) will, in all likelihood, vent, and roofs in this condition should be replaced.
In my (DF) OPINION, even here in McNulty's comments I suspect there is a mix of good science, authoritative source, and speculative opinions. For example his comment about attic moisture and roof ventilation.
The rate of moisture movement out through the roof structure of a humid or even wet attic is anything but uniform, with more water moving at plywood butt joints and penetrations than through the field of plywood 4x8' solid segments. So we ought to see moisture damage on the roof surface in a pattern that maps moisture migration openings.
For blistering, we don't.
Back in 1986 in the Boston Journal of Light Construction conference we learned that far more air and moisture movement, perhaps more than 90% of it, occurs at material joints and penetrations than through the field of the material, be it 1/2" drywall or 1/2" thick plywood.
Here are three helpful references for asphalt shingle blister rash causation & research:
[1] Cash, Carl G., and Frank W. Kan. "Finite Element Analysis of Racked vs. Traditionally Applied Three Tab, Seal Tab, Strip Shingles, and Blister Tests for Asphalt-Glass Felt Shingles." ASTM SPECIAL TECHNICAL PUBLICATION 1349 (1999): 123-131.
[2] McNulty, Raymond A. "COMPOSITION, PERFORMANCE, FUNCTION, AND STANDARDS." Interface (2000). [http://www.rci-online.org/interface/2000-01-mcnulty.pdf]
[3] Petty, Stephen E. "Attic and Crawlspace Ventilation." Forensic Engineering: Damage Assessments for Residential and Commercial Structures (2013): 437.
Our complete set of references on asphalt shingle blistering can be found at REFERENCES.

This page has been seen 44 times.

Users Browsing This Page (0 members, 1 guests)